Van mijn arabian night blijft rechter flipper bij starten spel omhoog staan, bij afleggen op deur openen valt flipper terug naar beneden.
Heeft iemand hier ervaring mee?
Grtn TomT
Rechter flipper staat omhoog
Re: Rechter flipper staat omhoog
kan rechterflipperknop zijn, en dan de flipperopto.
of transistor die de rechter flipperspoel stuurt is kapot en geeft constant door.
of transistor die de rechter flipperspoel stuurt is kapot en geeft constant door.
Re: Rechter flipper staat omhoog
Flipperknop werkt. Is transistor zelf te herstellen
Re: Rechter flipper staat omhoog
ja hoor, indien geen soldeer ervaring, best laten doen door iemand.
Q92 te vervangen op powerbord door een TIP102.
Q92 te vervangen op powerbord door een TIP102.
Re: Rechter flipper staat omhoog
kzou toch ook de flipperoptos eens kuisen met een wattestaafje.
en ook kijken dat de diodes op de flipperspoel niet los zitten.
en ook kijken dat de diodes op de flipperspoel niet los zitten.
Re: Rechter flipper staat omhoog
Electrical "Stuck Up" Problem:
Fliptronics Games:
Flipper cabinet switch is bad. On games with opto flipper cabinet switches, check the two opto boards. A bad or dirty opto can cause this problem. Flipper opto boards were implemented on Addams Family, mid-production (some Addams have them, some don't). On pre-opto flipper switch WPC games, check/clean the mechanical cabinet flipper switch.
Flipper gets very hot and eventually starts to burn and smell. This means the hold TIP102 transistor for that flipper is shorted on, and needs to be replaced.
Flipper immediately energizes and stays up when a game is started, or when the game turns on. The TIP36 transistor that controls the high voltage side of the coil is shorted on, and needs to be replaced.
Addams Family ONLY: The Addams Family pinball was the first Williams solidstate "fliptronics" game. It was the only game to use a "Fliptronics I" board (all later games used a "Fliptronics II" board). The Fliptronics I board has a unique personality. If both diodes on the right flipper coil (upper or lower) are missing or broken, as soon as the right flipper cabinet button is pressed in a game, both right flippers will stick in the "up" position. The right flippers will not release until the left flipper cabinet button is pressed! Note this MAY also happen if one diode on each right flipper coil is bad too. This problem can also happen to the left flipper, and is still related to coil diode failure. To fix this, check both right flipper coils and make sure the diodes are not broken or missing. Also make sure the left flipper coil's diodes are present and not damaged. Finally, sometimes a bad flipper diode will cause the Fliptronics I board's TIP102 hold transistor to fail. If the problem still exists after replacing the diodes on all the flipper coils, check the TIP102 hold transistor on the Fliptronics board.
Fliptronics Games:
Flipper cabinet switch is bad. On games with opto flipper cabinet switches, check the two opto boards. A bad or dirty opto can cause this problem. Flipper opto boards were implemented on Addams Family, mid-production (some Addams have them, some don't). On pre-opto flipper switch WPC games, check/clean the mechanical cabinet flipper switch.
Flipper gets very hot and eventually starts to burn and smell. This means the hold TIP102 transistor for that flipper is shorted on, and needs to be replaced.
Flipper immediately energizes and stays up when a game is started, or when the game turns on. The TIP36 transistor that controls the high voltage side of the coil is shorted on, and needs to be replaced.
Addams Family ONLY: The Addams Family pinball was the first Williams solidstate "fliptronics" game. It was the only game to use a "Fliptronics I" board (all later games used a "Fliptronics II" board). The Fliptronics I board has a unique personality. If both diodes on the right flipper coil (upper or lower) are missing or broken, as soon as the right flipper cabinet button is pressed in a game, both right flippers will stick in the "up" position. The right flippers will not release until the left flipper cabinet button is pressed! Note this MAY also happen if one diode on each right flipper coil is bad too. This problem can also happen to the left flipper, and is still related to coil diode failure. To fix this, check both right flipper coils and make sure the diodes are not broken or missing. Also make sure the left flipper coil's diodes are present and not damaged. Finally, sometimes a bad flipper diode will cause the Fliptronics I board's TIP102 hold transistor to fail. If the problem still exists after replacing the diodes on all the flipper coils, check the TIP102 hold transistor on the Fliptronics board.
Re: Rechter flipper staat omhoog
Bedankt